Volvo RWD 200 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 2/2008 200 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE    PRINT   SAVE 

Replaced ECU in '89 240...Car starts but won't keep running....Why? 200 1989

Newbie Question...I've replaced the ECU and the car now starts but only runs for 10-15 seconds. It will restart right away, but again only runs for a few seconds. I've also checked the fuel system relay and the air flow meter both checkout ok. What should I check next? Thanks!








  •   REPLY TO THIS MESSAGE    EDIT   PRINT   SAVE 

    What made you think that the ECU was bad? Assuming that the car wouldn't even start initially, then the ECU was probably bad since it will at least run now. Given that, I'd check the connector plug on the AMM. I had one of the little itty bitty prong things slide back when I was pushing the connector back onto the AMM. You'll have to examine the AMM connector closely. If there's a clip prong thingy that's pushed back up into the connector, then you'll need to get a little screwdriver or something to keep it in place when you re-connect the cable.

    If it ain't the ECU or the AMM, then I'd start looking at fuel delivery problems, i.e., fuel pump, filter, etc.
    Cabbie2169



    Mark this post as an answer to my question<- Use this feature to mark quality replies to your post.





  •   REPLY TO THIS MESSAGE    EDIT   PRINT   SAVE 

    I just sold an '89 ECU on E-bay. Was it you who bought it?

    I would also look at the AMM. Unplug it and see if the car will Idle for you.
    --
    '75 Jeep CJ5 345Hp ChevyPwrd, two motorcycles, '85 Pickup: The '89 Volvo is the newest vehicle I own. it wasn't Volvos safety , it was Longevity that sold me



    Mark this post as an answer to my question<- Use this feature to mark quality replies to your post.





  •   REPLY TO THIS MESSAGE    EDIT   PRINT   SAVE 

    Firstly explain why you changed the ECU... what was the problem.
    It could be one of many things now, you need to give more information.
    Check codes of course (see 700 faq, same thing)
    Could be AMM, temp sensor, ignition parts OK?, clogged cat, and others....



    Mark this post as an answer to my question<- Use this feature to mark quality replies to your post.





  •   REPLY TO THIS MESSAGE    EDIT   PRINT   SAVE 

    Just a thought...

    Check to see if throttle body is clean and the TPS is properly adjusted

    http://www.brickboard.com/FAQ/700-900/EngineFuelinjection.htm#ThrottleBodyandThrottlePositionSwitchAdjustment

    Good Luck
    Danny Mac



    Mark this post as an answer to my question<- Use this feature to mark quality replies to your post.





  •   REPLY TO THIS MESSAGE    EDIT   PRINT   SAVE 

    What codes does your new ECU give you? The code reader is under the hood on the driver side on the strut tower by the firewall. You will find tables for these codes in both Bentley and Haynes.
    --
    '89 244DL M47 162K miles



    Mark this post as an answer to my question<- Use this feature to mark quality replies to your post.




<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.