Volvo RWD 200 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 8/2008 200 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE    PRINT   SAVE 

Making a List 200 1984


This is my first posting on Brickboard. I would like to thank Brickboard and its contributors for filling many of my idle hours with engaging discussion about their Volvos, in particular, their 1980-era 240s.

As my nickname implies, I am very concerned about the future of our ailing national passenger railroad and dedicate countless hours to educating people about its importance. (I gave up flying 7 years ago and don't miss it a bit.)

I don't work on my car for the most part. I let the boys at Independent Volvo, in Albuquerque, NM sort out my problems and they always do an excellent job, at a very fair price.

I own a 1984 Volvo 244 GL and it serves me well. I have named her Stella II and she is the successor to Stella, the 1980 brick I once owned. I have come to respect and love my Volvo because she has never, ever let me down. Even when it lost its ground on the freeway recently, she had the decency to drop dead at the end of the exit ramp.

The only car that I hold in higher esteem than a Volvo is a 1965 Ford Falcon, but that is because it was the very first car that I ever owned.

OK, now you know a little bit about me and my car, let me explain why I am posting here. I am due to bring my car into the shop on Friday and the guys at the shop like it when I make a "list." But before I make a "list" I was wondering if I could bounce a few things off you guys and get your opinions.

First off, I noticed that the rubber "boot" (I guess you'd call it), that surrounds the base of the gear shifter has disengaged from its footing. Without a proper footing, the air from the engine pours into the passenger compartment, and lets in a bit of noise. Since the clutch assembly was replaced only a couple years ago, I was wondering if you think the rubber boot was defective or improperly installed. Or is this just a basic maintenance issue? (i.e. Just one of those things...)

Second, I think the blackstone radiator has about 20 years on it and was wondering if you think it might be a good idea to replace it with a new or refurbished 3-core unit? 20 years seems like a long time to me and although I have read postings that say the Blackstone is a good, sturdy radiator, it has been my experience that all automotive parts eventually fail.

Third, the air conditioner does not work. Well, it worked for about a week after I bought it but then it seemed to release all its Freon and has not worked since. I am wondering what success you all have had with making that R-whatever transformation in the system. Wouldn't it make more sense just to replace the compressor than to try to rebuild it?

Thank you for reading this long, drawn-out posting. And next time you are thinking about taking a long trip, consider climbing aboard Amtrak!









  •   REPLY TO THIS MESSAGE    PRINT   SAVE 

    Making a List 200 1984

    You can use bolts to replace the plastic boot holdowns.

    If the rad is cooling, has no leaks and the corrugations aren't crumbling (press a finger on lower part of rad to see if they give) then replacement is optional.
    --
    1980 245 Canadian B21A with SU carb and M46 trans








  •   REPLY TO THIS MESSAGE    PRINT   SAVE 

    Making a List 200 1984

    You beat me by a year, my Blackstone only lasted 19 years! It finally broke at the top radiator hose, the radiator was in fine shape but the plastic got old and gave up.

    Radiators are easy to replace and it would make a great first DIY job. Also replace the thermostat and both radiator hoses. Get a new all copper 3 row core and change the antifreeze every 2 years. If the water pump is of unknown age you might want to consider replacing it and fan belts at this time. Also an easy DIY job.

    I used to live in Albuquerque and loved driving up to Sandia peak for skiing or the fun of it, beautiful country. Good luck Dan
    --
    85 245 M46 192K, 92 245 A70 119K








  •   REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

    Making a List 200 1984

    I love riding trains, they just never seem to be going where I need to end up.

    The shifter boot is held on by 4 plastic fasteners. Some mechanics will try to reuse them and oftimes, they eventually fail. Sometimes the boot itself will tear around the holes. In that case you should replace it.

    Twenty years is a looong time for a radiator, especially in an environment like New Mexico. You must take good care of your cooling system. I guess I'm from the "If it ain't broke, don't fix it" school, but after 20+ years, a new rad could be considered good preventative maintenance ;-)

    There have been a ton of posts recently about A/C and conversions. Search the archives for the past month or so. I'm sticking with R-12 for now in the 240. The stuff was expensive, but if I can keep the system sealed, it will be worth it, it's cooold.

    --
    don hodgdon '89 744ti, '81 242t, '71 D-35








  •   REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

    Making a List 200 1984

    Hello,

    I just did the clutch on my 82 and had to replace a foam seal around the gear shaft that blocks noise and heat from coming into the cabin from below. They most likely left it out or put back the original in poor shape. Also the boot is held on with 4 small push on clips that attach to the floor under the rug. They may be missing, (PITA) to replace, or the mounting holes on the boot got ripped when it was removed. Hope that helps.

    Mario







<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.