Volvo RWD 200 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 9/2004 200 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  skiman26 on  Fri May 23 20:17 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Aug 4 21:08 CST 2014
[RELATED]

Just replaced all of the gaskets from the intermediate housing back on my 85' M46.

They were almost paper thin and we almost added silicone, but decided against it.

Just hopped under the car and there is a decent drip where the intermediate housing and the
transmission meet.

I've checked IPD for a good green gasket, but can't seem to find what I need.

Any other recommendations?

Thanks








  REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  David Samuels on  Wed May 28 07:55 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Oct 20 12:23 CST 2014
[RELATED]

Do you know about Duane? The OD Guru? odguru@kc.rr dot com








  REPLY TO THIS MESSAGE    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  ODGuru on  Sat May 24 08:38 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Sat Oct 4 18:52 CST 2014
[RELATED]

Did you replace the plastic crush seals under the top two nuts that hold the housings and brake ring together? That type of seal is a one use only.

An alternative if you do not have the crush seals is a copper washer that fits the recess on the case drilled to the 5/16 bolt size. Or a Nylon washer fitting the recess with a steel washer over.

I've torn a few of the thinner paper ones on install but never had them leak.

Duane








  REPLY TO THIS MESSAGE    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  skiman26 on  Tue May 27 21:04 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Aug 4 21:08 CST 2014
[RELATED]

We've taken apart the overdrive and intermediate housing and can't find any
crush washers or any place a washer could go.

Any pictures for reference? I might not be looking in the right place.

thanks








  REPLY TO THIS MESSAGE    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  skiman26 on  Sat May 24 18:58 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Mon Aug 4 21:08 CST 2014
[RELATED]

I really doubt we did that, thanks for the info.

Back on the lift she goes!








  REPLY TO THIS MESSAGE    PRINT   SAVE 

Looking for a reliable OD intermediate housing gasket 200

posted by  benski on  Sun May 25 05:34 CST 2014
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Wed Oct 22 12:07 CST 2014
[RELATED]

Is it something you can make? Ball peen hammer and a punch set?







<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.