Volvo RWD 200 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 12/2005 200 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

selector shaft seals install, 92 245 tranny--what to know critically? 200

posted by  bcg on  Thu Oct 7 18:51 CST 2004
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Sun Jul 27 08:12 CST 2014
[RELATED]


I'm about to replace my 92 245's tranny selector shaft seals, both sides.

first time doing this.

any recommendations?
anything that's needed to know?
do i need special seal tools?

thanks much again!

byron golden
86 245, 246k mi
92 245, 136k mi








  •   REPLY TO THIS MESSAGE    PRINT   SAVE 

    selector shaft seals install, 92 245 tranny--what to know critically? 200

    posted by  skim35 on  Fri Oct 8 05:25 CST 2004
    Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS] [RELATED]

    The right side, you will need to remove exhuast to get to the seal.

    You can slide a small screw driver or a stiff paper clip to remove the old seal. Careful not to scretch the mating surface.

    When installing, use small socket.








    •   REPLY TO THIS MESSAGE    PRINT   SAVE 

      selector shaft seals install, 92 245 tranny--what to know critically? 200

      posted by  bcg on  Fri Oct 8 07:17 CST 2004
      Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
      last visit: Sun Jul 27 08:12 CST 2014
      [RELATED]



      Thanks skim, for the great tips, i just bought the bushings today and will work on the car tomorrow.

      regards,
      byron








  •   REPLY TO THIS MESSAGE    PRINT   SAVE 

    selector shaft seals install, 92 245 tranny--what to know critically? 200

    posted by  Chris Mullet on  Fri Oct 8 01:42 CST 2004
    Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
    last visit: Fri Oct 24 09:08 CST 2014
    [RELATED]

    Just the standard precautions - don't gouge up the casing or shaft removing the old seal. Wipe everything clean before sliding the new one on. A tiny bit of grease rubbed on the shaft will help the new one slide on.








    •   REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

      selector shaft seals install, 92 245 tranny--what to know critically? 200

      posted by  bcg on  Fri Oct 8 07:18 CST 2004
      Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
      last visit: Sun Jul 27 08:12 CST 2014
      [RELATED]


      Thanks Chris, i got the bushings today, pretty cheap from volvo dealer.

      i did get some degreaser and some compressed air in a can. will do the job tomorrow.

      thanks for the suggestions. i'm following them.

      regards,
      byron







<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.