Volvo RWD 200 Forum

INDEX FOR 10/2025(CURRENT) INDEX FOR 10/2010 200 INDEX

[<<]  [>>]


THREADED THREADED EXPANDED FLAT PRINT ALL
MESSAGES IN THIS THREAD




  REPLY TO THIS MESSAGE    PRINT   SAVE 

How do I replace the clamp that holds the cat to the rest of the exhaust? 200 1982

posted by  82silver240turbo on  Tue Jul 29 11:53 CST 2003
Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
last visit: Wed Sep 11 05:37 CST 2013
[RELATED]

In an attempt to make the removal of my catalytic converter easier I chose to hacksaw the bolts that tighten the clamp that holds the cat to the rest of the exhaust system. Now it seems the bolts are part of the clamp, or at least are now after years of exposure. I am not sure if the cut ends of the bolts can be removed from the clamp, so I am wondering if the clamp itself can be removed and replaced or if it is a standard piece of the exhuast that comes as part of the pipe. Anyway, I was wondering if anyone could give me any advice on what I could or should do?
Thanks








  •   REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

    How do I replace the clamp that holds the cat to the rest of the exhaust? 200 1982

    posted by  Don Foster on  Tue Jul 29 13:01 CST 2003
    Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
    last visit: Sun Oct 5 11:53 CST 2014
    [RELATED]

    "...clamp that holds the cat to the rest of the exhaust system..."

    I assume you mean the three bolts that holds the flanges together where the front pipe mates to the cat.

    Drill 'em out so you can reconnect everything using fresh bolts (with nuts).

    Works every time.

    Wear safety glasses while drilling.

    New gasket is advised.
    --
    Don Foster (near Cape Cod, MA)








    •   REPLY TO THIS MESSAGE    PRINT   SAVE 

      How do I replace the clamp that holds the cat to the rest of the exhaust? 200 1982

      posted by  82silver240turbo on  Tue Jul 29 20:23 CST 2003
      Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
      last visit: Wed Sep 11 05:37 CST 2013
      [RELATED]

      Thanks buddy. Is the flange on the muffler end removable. I dont see a way to remove it? How near Cape Cod are you? I travel between amherst and onset.








      •   REPLY TO THIS MESSAGE Replies to this message will be emailed.    PRINT   SAVE 

        How do I replace the clamp that holds the cat to the rest of the exhaust? 200 1982

        posted by  Don Foster on  Wed Jul 30 00:57 CST 2003
        Author: [PROFILE] [EVERY POST] [THREADS] [BEST POSTS] RSS Feed     [IGNORE ALL POSTS]
        last visit: Sun Oct 5 11:53 CST 2014
        [RELATED]

        The flanges are welded to the pipes, not removable.

        I grew up in Woods Hole, still have family there. I'm about 30 minutes from the bridge -- check my profile.
        --
        Don Foster (near Cape Cod, MA)







<< < > >>



©Jarrod Stenberg 1997-2022. All material except where indicated.


All participants agree to these terms.

Brickboard.com is not affiliated with nor sponsored by AB Volvo, Volvo Car Corporation, Volvo Cars of North America, Inc. or Ford Motor Company. Brickboard.com is a Volvo owner/enthusiast site, similar to a club, and does not intend to pose as an official Volvo site. The official Volvo site can be found here.